Inert Welrod Replica

Cold War, Complete builds, pistol, Suppressed, Weapons, Welrod, WWII

This is a little side-project I have been working on due to several requests. This replica Welrod is almost entirely 3D printed. I’ll be offering it in kit and complete form.

_DSC7848

The trigger and grip safety are both sprung.

_DSC7849

Both rear and foresight have blobs of phosphorescent paint to simulate the glowing radio-luminescent sights

_DSC7850

The bolt opens and locks like the original.

_DSC7851

It has a detachable magazine.

_DSC7852

And the shroud can be removed to access the suppressor and barrel.

_DSC7853

The suppressor internals, showing the spacers, rubber wipes and washers.

_DSC7857

And the rebated muzzle, which allowed the gasses to expand a bit for a slightly tidier kill when used pushed up against the body of an unsuspecting target.

_DSC7855

If you are interested in this project or have an idea of your own, drop us a line on enquiries.vintageairsoft@gmail.com to discuss. ‘Like’ our Facebook page or follow the blog to get regular updates on projects and interesting videos and articles.

 

Don’t forget you can buy our smaller items via Etsy. Our larger items can be found here.

Sten MkI/MkI* : Complete

Add-on kits, Complete builds, Products, Sten, Sub Machine-guns, Weapons, WWII

Some images of the completed Sten MkI and MkI*. Firstly a picture of AN original for comparison. I should point out that you can find differences between nearly every surviving example so this isn’t definitive:

tumblr_mky4fuYlFr1s57vgxo1_1280

The main issue with this replica is that the safety catch is at the top of the operating handle slot (as this is based on the AGM Sten MkII). The only way to adequately redo this is to make a whole new receiver unit. Maybe a project for the future…

_DSF7039

A close up of the receiver. The new operating handle and bolt also feature the Sten safety switch kit. You can also just make out the Sten MkI stampings on the magazine housing.

_DSF7040

The foresight on this is very comfortable to acquire, at least in the confines of the workshop where I have tested it so far! This will be going out in the field at the weekend.

_DSF7042

The stock is very comfortable compared to the MkII T-stock. That said clutching a thistle is an improvement over the T-stock… But in all seriousness this is a great alternative and is fast becoming a personal favourite.

_DSF7043

One final feature worth noting is the battery compartment. Accessible from the rear, it can just about fit the standard stick battery in it, though a stick lipo would be a far easier fit.

_DSF7045

And in the Sten MkI* configuration, once it had been optimised by the Singer company for serial production:

_DSF7044

This kit will be for sale on our Etsy page HERE in due course. If you like the look of this gun and would like a build of your own that we don’t currently offer please do get in touch! Email us on enquiries.vintageairsoft@gmail.com or get in touch via our Facebook page.

The Sten MkI/MkI*

Add-on kits, History, Sten, Sub Machine-guns, Weapons, WWII

History

After the swift and brutal defeat of the British Expeditionary Force and their allies in the Battle of France and the retreat from Dunkirk across the channel, Britain was desperate for equipment and armament. All heavy weapons, vehicles and most small arms were left behind.

Dunkirk_26-29_May_1940_NYP68075

As a result there was a huge push to re-arm as quickly as possible. As well as all of Britain’s manufacturing being turned to the war effort, the War Office bought every Thompson sub-machine gun the USA could build. The US couldn’t keep up with demand however and with losses to U-boats in the Atlantic Britain needed to produce their own sub-machine gun.

churchill_decides_to_fight_on

The result of this was the Sten Machine Carbine. The prototype was a complex piece of engineering, requiring a multitude of machining actions to produce. When handed over to the Singer company to produce, a host of improvements were made to make the gun suitable for mass production.

tumblr_mky4fuYlFr1s57vgxo1_1280

I wanted to develop a kit to temporarily modify the AGM Sten MkII to a MkI/MkI* for early war impressions and, frankly, for an interesting regular game gun.

The build

Step one was to build the flash hider/muzzle rise compensator. This large scoop is formed from a piece of steel cut to shape and beaten on a former.

_DSF5319

This could then be welded shut and a short piece of tube welded on the back to mount it. The sling loop is a piece of thick wire, welded shut. I turned a piece of nylon bar to size to fit round the mounting tube and inside the heat sleeve.

_DSF6353

This can then be slid into the heat sleeve. The photograph below shows the front sight mounted. This is mild steel, laser cut to shape and bent by hand.

_DSF6991

To create the buttstock, I needed to bend steel tube to shape. As I don’t have a tube bending jig and a spring bending system would produce too shallow a bend. Cutting out a section like this, bending to shape and welding closed makes for a neat, controlled bend.

_DSF6976

This could be welded onto the backplate and buttplate. The top tube also functions as the battery tube and the plan is to have the battery accessed from the back.

_DSF6985

At this point, this is pretty well what the MkI* looked like (as far as one can tell, photographic evidence is limited) as it has all the woodwork removed for simpler manufacture.

_DSF6984

Woodwork is needed to complete the MkI of course, the foregrip being an important part of the design that was sadly deleted on later models until the introduction of the MkV.

I made this woodwork right back at the beginning on Vintage Airsoft at the end of 2014, it has been sitting waiting for me to finish this project all this time!

_DSF6988

_DSF6987

There are a few last bits to finish, namely removing the MkII fore-sight and stamping the magazine well with the correct information. The only major inaccuracy will be the safety catch location. On the MkI Sten this was actually below the operating handle slot but was moved to the top on all later models.

More photographs to follow with the completion of the build!

Like the look of this build? Why not email us on enquiries.vintageairsoft@gmail.com to find out more. While you’re in a gun mood, check out our Etsy page where we have ready-made kits and accessories.

P.S.: I am looking for any original images of the Sten MkI or MkI* in use by soldiers. These seem to be almost non-existent so if any readers have such images please do send them in.

P.P.S.: For more information on the development of the Sten Machine Carbine and some beautiful pictures of an original Sten MkI, see here.

What’s in store for 2015?

Add-on kits, Products, Rifles, Sub Machine-guns, WWII

Having ‘opened shop’ about a month ago, we’ve had a great deal of interest in our products, it’s quite exciting! The first kit for a customer is due to be dispatched this week, one of the Sten MkVs.

_DSF4663

The production version of this kit (see the prototype here) is a little different from the prototype we showed earlier. There are a couple of external differences: we have added a (real steel) sling swivel to the top of the buttstock and the pistol grip has changed shape slightly to more accurately reflect the original.

Inside we have made some changes too. Due to a request from the customer we have tweaked the battery compartment so that it can accept a LiPo battery. We also made space for the stick battery in case he ever needs to use them.

_DSF4670

Due to the upgrades, this version will be a little more expensive than the prototype at £145 as it does cost more to buy in parts and a bit longer to make.

So, what is in store for 2015? We have a few Sten kits due for release in the first two months as well as two custom projects in the pipeline.

Dom really wants to build some realistic bolt-action rifles with the magazines in the correct place: something seriously lacking in affordable period rifles, he has the design, just not the funds!

Dave is developing an AEG version of a very popular series of carbines that is currently only available in a gas version (unless you count the horrendous plastic ones).

If you are interested in sponsoring a build project or a kit or have your own custom build in mind, do let us know! enquiries.vintageairsoft@gmail.com

 

Merry Christmas from us here at Vintage Airsoft!

The ‘realism’ kit, and a teaser

Add-on kits, Sub Machine-guns, WWII

20141125_173616

Some of you may have noticed that in the MkV post, my Sten looked a bit different from the standard ASG Sten (and not just because of the load of wood attached to it!). Due to the shape of the AEG internals, it is not possible to fit a real steel spring so I made up a jig that would allow me to bend some wire to a consistent angle repeatedly.

This created a wire zig-zagged like half a spring, but flat. Pressing this along the outside of the Sten longways bends it roughly to shape for the inside of the gun. Although it can be inserted through the back of the gun, I found that it made the ‘spring’ get stuck on the back of the gearbox. Instead, I removed the fore-end and slid it in backwards, easing it along with a pair of pliers.

The fake bolt-carrier I used is actually made from a sardine tin lid. The finish on this is of course rustproof within reason, making it ideal. Again, I bent it to shape outside the Sten and just slid it in through the fore-end. In the longer run, I plan on replacing this with a piece of brass sheet and offering it as a kit, once I have made a cover for the rather ugly hex-bolt that comes with the original gun.

 

 

And why is this post a teaser? The first picture is a clue to my next project for release…

Dom

Hello and Welcome

Uncategorized

Hello there, welcome to Vintage Airsoft!

We are a group of airsofters who have a special interest in more unusual firearms that are not always available or affordable for airsoft. As well as developing kits for airsoft guns already made by other manufacturers, we are looking for opportunities to collaborate with individuals who want something a little bit special. Whether it’s anti-tank or something lightweight we would love to hear from you to help us develop something new.

On this blog we will be showing off our newest products, show a little of the process that goes into designing and building them and hopefully some skirmish reviews in the longer run.

We look forward to hearing from you.

Dom and Dave

 

We can be contacted at:

enquiries.vintageairsoft@gmail.com