Inert Welrod Replica

Cold War, Complete builds, pistol, Suppressed, Weapons, Welrod, WWII

This is a little side-project I have been working on due to several requests. This replica Welrod is almost entirely 3D printed. I’ll be offering it in kit and complete form.

_DSC7848

The trigger and grip safety are both sprung.

_DSC7849

Both rear and foresight have blobs of phosphorescent paint to simulate the glowing radio-luminescent sights

_DSC7850

The bolt opens and locks like the original.

_DSC7851

It has a detachable magazine.

_DSC7852

And the shroud can be removed to access the suppressor and barrel.

_DSC7853

The suppressor internals, showing the spacers, rubber wipes and washers.

_DSC7857

And the rebated muzzle, which allowed the gasses to expand a bit for a slightly tidier kill when used pushed up against the body of an unsuspecting target.

_DSC7855

If you are interested in this project or have an idea of your own, drop us a line on enquiries.vintageairsoft@gmail.com to discuss. ‘Like’ our Facebook page or follow the blog to get regular updates on projects and interesting videos and articles.

 

Don’t forget you can buy our smaller items via Etsy. Our larger items can be found here.

Advertisements

Sten MkIV: Build

Custom builds, Sten, Sten MkIV, Sub Machine-guns, Weapons, WWII

The first major hurdle for me was that my Sten was missing the massive chunk of aluminium that houses the barrel and hop up unit. I measured up one from another gun and created a 3D model to be printed. I added a section to the front for the flash hider which is a separate piece. Running through this and the other part is some 16mm steel tube for strength.

_DSC7456

The stock is made from pieces of laser cut steel. For the very sharp bends I made cuts with the angle grinder, made the folds and welded them up.

25286946_10213410104599833_1018159191_n

The locking bar is kept in place with two screws. These ride in slots that stop it from travelling too far back or forwards.

25346365_10213410104799838_380360761_o

The pistol grip slotted into place, welded on the bottom which was then ground flat to allow the stock to pivot. The trigger guard is huge, the bend was made with wooden formers and the shape was checked against my paper template.

25344367_10213410107479905_1901161622_o

A close-up of the locking system. This is a pretty solid system, with only the wobble you would expect from a typical Sten stock.

25397994_10213410106679885_612810655_o

Once the stock unit was welded onto the backplate, this really started to take shape. Shown below with the stock stowed.

25353157_10213409215617609_250685353_o

And the stock deployed. So far it’s more comfortable than it looks, the next step is to make the wooden grips.

_DSC7579

These are made from some leftover walnut I had sitting around. I printed a paper template, cut them out and drilled the screw holes. Then fine fitting and shaping was done with files and the electric hand sander.

_DSC7590

Then it was time to strip everything and finish her up.

_DSC7592

The grips got a quick soaking with some dark red woodstain, followed by hardwax oil.

_DSC7594

All that’s left now is reassembly, fitting a foresight and doing some internal work on the Sten. I’ve swapped the barrel out already for a shorter one but the trigger needs some TLC.

You can see the complete item here.

If you are interested in this project or have an idea of your own, drop us a line on enquiries.vintageairsoft@gmail.com to discuss. ‘Like’ our Facebook page or follow the blog to get regular updates on projects and interesting videos and articles. 

Don’t forget you can buy our smaller items via Etsy. Our larger items can be found here.

Sten MkIV: Introduction

Sten MkIV, Sub Machine-guns, Weapons, WWII

The Sten MkIV has very little written on it, so this introduction will be rather short.

11. Mk 4 sn 3_Web

It was an experimental design to make Britain’s Sub machine gun more compact. This has several possible reasons, but the most likely seeming to my eye (lacking access to original documents) is the Airborne theory. A more compact sub-machine gun than the standard Sten MkII and MkII would make sense for airborne troops and this definitely meets that requirement.

This was ultimately met by the Mk5, which could have its buttstock removed and replaced with a blank backplate.

There were two versions of the MkIV, the ‘A’ which had a hand guard style trigger guard (some say to accommodate arctic mittens) and the ‘B’ which has the trigger and pistol grip advanced to halfway down the receiver. This was apparently an improvement but not enough it would seem!

fjktqa

The reason the MkIV was rejected during trials was that it was ‘uncomfortable to fire’. This does seem a little bit ironic seeing it was designed to replace the ergonomics-violating MkII and MkIIIs, but judging by what was eventually adopted the general effort was towards a significantly better gun comfort wise rather than a slight improvement.

 

The other possibility is that, being much smaller in the body than a ‘normal’ Sten (especially in the barrel) the recoil, muzzle blast or ejection may have been pretty bad. It’s pretty much impossible to say without access to trials reports or getting to fire the (so far as I can tell) only remaining piece at the Royal Armouries. I suspect it will grow legs and walk out before I am allowed to do that however!

large_DI_2012_0648

I’ll be making a MkIVa replica based on the example in the Royal Armouries, as a bit of  change of scene from the bolt actions and machine guns I’ve been building a lot lately!

You can see the build and completed item here. You can see more Sten projects here.

If you are interested in this project or have an idea of your own, drop us a line on enquiries.vintageairsoft@gmail.com to discuss. ‘Like’ our Facebook page or follow the blog to get regular updates on projects and interesting videos and articles. 

Don’t forget you can buy our smaller items via Etsy. Our larger items can be found here.

P.S.: Bonus photo of a suppressed MkIVa apparently in the NFC, Leeds.

Suppressed Mk 4A(S)Sten - National Firearms Centre, Leeds, UK (Photo by Frank Iannamico)

Sten MkIV: Complete

Complete builds, Products, Sten, Sten MkIV, Sub Machine-guns, Weapons, WWII

The completed Sten MkIV. Perhaps not a looker, but definitely one of the most practical SMGs I have built to date. When folded, this easily fits in a backpack making it a much more portable choice than my usual long rifles.

_DSC7835

The large trigger guard makes it ideal for use with gloves in cold conditions.

_DSC7836

The buttstock when folded also makes a handy foregrip. In CQB this is very practical for when poking round corners.

_DSC7838

When  you want a little more shooting precision, just grab the inner tongue and pull it towards the buttstock.

_DSC7840

You can then unfold the stock and lock it into position at the back.

_DSC7844

This is pretty comfortable in this layout, though I am not sure if recoil would be easy to control. I can see how the flat steel would be uncomfortable for prolonged periods of shooting, but no more so than many of the previous models of Sten gun. Frankly compared to the prolific T-stock this would still be a huge improvement so I don’t understand how this was rejected due to being uncomfortable while shooting.

_DSC7846

 

If you missed it, you can see the build post for this project here.

If you are interested in this project or have an idea of your own, drop us a line on enquiries.vintageairsoft@gmail.com to discuss. ‘Like’ our Facebook page or follow the blog to get regular updates on projects and interesting videos and articles. 

Don’t forget you can buy our smaller items via Etsy. Our larger items can be found here.

G43 AEG Mk2: Complete

Battle Rifles, Complete builds, Custom builds, G43 MkII, G43/K43, Weapons, WWII

I know some people are quite excited about this project so let’s get straight stuck straight in with some pictures!

Left side:

_DSC7820

Right side:

_DSC7821

The 3D printed receiver.

_DSC7822

The rear sight, adjustable for elevation via the leaf. The rear sight adjustment is controlled by the bar across the leaf which is held in place by teeth and spring tension.

_DSC7823

The receiver open. You can now see the finishing touches to the slide, which has been painted up using a mix of acrylics and coarse sand. This simulates the rough cast surfaces left over that were not milled flat as a manufacturing expediency.

_DSC7827

The foresight unit, 3D printed and pinned in place. The blade is adjustable for windage once the hood is removed.

_DSC7825

The barrel is black painted. Production versions of this may be oil blacked, though the fore-end cap will likely be printed rather than metal.

_DSC7826

The magazine well and trigger guard. I may have to beef up the trigger guard in future versions. The magazine release is the small catch between the  magazine and the guard. Although not greatly ergonomic, the original was designed to be fed with stripper clips to be fair.

_DSC7828

A second view.

_DSC7833

The buttstock needs a bit more work for production, but it’s a satisfying result. For production I am going to try and put a sling mounting through it as per the original.

_DSC7829

The buttplate comes off to access the battery compartment.

_DSC7830

A quick view down the gun from the back.

_DSC7832

I’m very pleased with this build I must admit. It looks the part and has a nice heft to it. Of course there have had to be some dimensional changes to fit the airsoft internals, but they aren’t any worse than AEG M1 Garands and without a direct comparison it ought not stand out too much.

Finally WWII airsofters have an option for a rifle that isn’t a K98k or an STG44.

 

If you have enjoyed this project or have an idea of your own, drop us a line on enquiries.vintageairsoft@gmail.com to discuss. ‘Like’ our Facebook page or follow the blog to get regular updates on projects and interesting videos and articles.

Don’t forget you can buy our smaller items via Etsy. Our larger items can be found here.

 

 

Enfield No.5 Mk 1: Complete

Cold War, Complete builds, Custom builds, Lee-Enfield, No. 5 Enfield, Rifles, Weapons, WWII

Well, the No.5 Enfield is complete! And she ain’t a bad looker though I say so myself. Not to mention as far as I know the world’s first Airsoft Enfield No.5.

Let’s talk through her from back to front.

_DSC7471

The buttpad is hard rubber, in an ABS 3D printed cage re-enforced with Polymorph.

_DSC7475

The 3D printed receiver covers the VSR internals for the most part. The trigger is a little square, I’ll probably round it off more for a comfort.

_DSC7476

The rear sight. A bit of tinkering and I may even make it so that I can use the ladder sight for longer range use. For my purposes at present however (a 1 Joule rifle for close, quiet use) the battle sight is just what I need.

_DSC7478

When testing, the windage adjustment in the foresight was very useful. I’ll have to add some elevation adjustment as well as that would come in handy.

_DSC7477

The hop adjustment the most discrete I’ve done on an Enfield yet. That little hole in the top guard is the TDC hop adjustment.

_DSC7479

The magazine well is my standard VSR quick-load magwell. Ideal for the close work I intend to use it for.

_DSC7568

Last but not least, the rear sling bracket. Distinct and unique to the No.5 carbine, this makes an odd pairing with the conventional forward sling swivel. That said I have found it quite comfortable in use, with the gun swinging around less than with conventional swivels.

_DSC7566

 

If you have enjoyed this project or have an idea of your own, drop us a line on enquiries.vintageairsoft@gmail.com to discuss. ‘Like’ our Facebook page or follow the blog to get regular updates on projects and interesting videos and articles.

You can see the build for this rifle here.

Don’t forget you can buy our smaller items via Etsy. Our larger items can be found here.

 

Enfield No.5 Mk 1 Build: Part 2

Cold War, Custom builds, No. 5 Enfield, Weapons, WWII

Part two starts with the receiver which has been 3D printed. I’m very pleased with the way the markings have come out on this, especially after painting up.

_DSC7433 The rear sight fits in quite well, just needing a little filing down in the mountings for a snug fit.

_DSC7434   _DSC7435  

Fitted in the stock, the receiver sits in a cutout on the left, the right is concealed in the stock itself.

_DSC7451

It took a little tinkering to get the top guard to fit, but it is now secured under the front of the receiver and at the front by the front band.

_DSC7453

Once I checked all the parts fitted well, I stripped the wood away. I applied my red-brown stain blend that I use for my Sten Mk5 kits. 

_DSC7455

Once this had settled in, I applied a coat of slightly thinned hardwax oil, for a fairly hardwearing semi-gloss finish. 

_DSC7458

Finally, the resin faux magazine is expoxied into place. Once set, I’ll paint it up and she’ll basically be done!

_DSC7467

 

Pics of the completed rifle to follow soon.

 

If you are interested in this project or have an idea of your own, drop us a line on enquiries.vintageairsoft@gmail.com to discuss. ‘Like’ our Facebook page or follow the blog to get regular updates on projects and interesting videos and articles. 

Don’t forget you can buy our smaller items via Etsy. Our larger items can be found here.

 

G43 AEG Build 2: Part 3

Battle Rifles, G43 MkII, Weapons, WWII

The last leg of the G43 build are the details that will make it really look the part. First up: the rear sight leaf. This is adjustable for elevation, using a spring and teeth that engage on the right side of the leaf.

Screen Shot 2017-11-04 at 18.21.47

At the front, I’ve had a spring 3D printed. This slots into the nose cap provided by the client.

_DSC7418

At the back of the receiver, the new one has the disassembly lever.

_DSC7416

The rear sight in the flesh. It is kept down by the spring in the front of it.

_DSC7411

Eagle eyed viewers will notice that the receiver has changed a bit, there are now two scoops in the side up by the chamber. There are also stronger rails which had proven a little bit weak to stand up to repeated disassembly.

_DSC7402

The rear sight in place on the new receiver. 

_DSC7446

The foresight is pinned in place with two 3mm pins. The foresight blade is adjustable for windage, so with the rear sight elevation adjustable you have a good range of adjustment.

_DSC7448
 

Although this is now nominally all in place, I need to do some last bits of finishing. Although it is all there there is something missing to give it that ‘X-factor’. I expect it’ll all come together once the painting has been done.

 

If you are interested in this project or have an idea of your own, drop us a line on enquiries.vintageairsoft@gmail.com to discuss. ‘Like’ our Facebook page or follow the blog to get regular updates on projects and interesting videos and articles. 

Don’t forget you can buy our complete products via Etsy.

 

Enfield No.5 Mk 1, the ‘Jungle Carbine’: Introduction

Cold War, Lee-Enfield, No. 5 Enfield, Weapons, WWII

Mention the No.5 Lee-Enfield rifle and you will always get a reaction. It is one of the most controversial British small arms, beaten only by the SA80 system and the EM-2.

 

 

The idea of the No.5 was to create a shorter, handier and lighter version of the British service rifle, the Enfield No.4. This had already seen some upgrades from its predecessor the No.1 MkIII. Contrary to popular belief, this effort to lighten and shorten the Enfield design was not specifically to aid in jungle fighting (though this was clearly on the Empire’s radar) it was, in fact to provide Airborne troops with a rifle less awkward to carry in the confines of an aircraft.

PARATROOP TRAINING AT NETHERAVON,WILTSHIRE, NOVEMBER 1942

Climbing into a Hotspur glider during training. Although glider design improved on this compact format you can see where the desire for a handier weapon came from.

 

This it certainly achieved, it is around 2lbs (0.9kg) lighter and nearly 5″ (125mm) shorter. Most of this saving was achieved by shortening the barrel, though also through lightening cuts around the receiver to remove excess material and lightened versions of certain components (such as the bolt handle and trigger guard/magwell).

 

8dd2fa79152dcedc600b3c9d3c9483c6

As a result of this shortened barrel, a flash hider was added. The length of the standard rifles meant that most of the .303 cartridge load was effectively used and produced only a (relatively) usable muzzle flash. The No.5 however has a significant muzzle flash, which could be blinding to the shooter in low-light conditions. The flash hider is not actually there to hide the flash from the enemy, it’s to hide it from the user.

 

22500a153a3b835a1ba0e9f29c0e7548--mk--palestine

As a result of the lightening, perceived recoil is also greater. To counteract this, the designers added a rubber butt-pad in place of the traditional brass or steel plate. A good idea, except that they made it very small, a bulging pad missing out a lot of the butt’s surface area. So that increased perceived recoil was forced into an even smaller part of the shoulder. Thank goodness it was comfy, soft rubber right? Err, well concerns around durability meant that a pretty hard rubber compound was used. Not great at the time and 70 years on they have only grown harder.

4282786

The controversy was that these rifles allegedly suffered from a ‘wondering zero’. This means that once sighted in, the rifle would not hit the same aimed point consistently. This was the reason the War Office gave for discontinuation of No.5 production in 1947, only three years after is was introduced. This makes it one of the only military service rifles to be outlived by its predecessor.

Several aspects of the rifle design have been suggested as causes including:

-The lightening cuts causing the receiver to flex when fired. This could cause headspace issues or inconsistency between shots over time

-The flash hider if fitted incorrectly or damaged may cause gas imbalances around the projectile, allowing shots to wonder of their typical course

 

Modern No.5 MkI owners have been unable to reproduce this wondering zero effect, which makes it look likely that this was only given as an excuse to shift bolt-actions to the rear echelons and give them in aid to allies to speed up introduction of the self-loading rifle that every other major power was adopting or had already.

9db539a5577d0f41031b93101f5b3a92--lee-enfield-commonwealth

Nevertheless, the No.5 saw limited service in Northern Europe, notably during the liberation of Norway, but most of its service life was post WWII, in Korea and Malaya, where they were not only used by British troops but also local forces.

malayan-emergency-no-5-jungle-commando-short-magazine-lee-enfield-smle-dayak-tracker

For an outline on the No.5 MkI, see Ian’s video at Forgotten Weapons.

For some in-depth information, see C&Rsenal’s article on the rifle, including how to spot the many fakes available.

When the build posts go up, you can see the progress here.

8ff67f7d5e1b5af4c1ae461625c83b0f--malayan-emergency-british-soldier

 

 

If enjoyed this piece or have an idea of your own, drop us a line on enquiries.vintageairsoft@gmail.com to discuss. ‘Like’ our Facebook page or follow the blog to get regular updates on projects and interesting videos and articles.

Don’t forget you can buy some of our complete products via Etsy

Enfield No.5 Mk 1 Build: Part 1

Cold War, Lee-Enfield, No. 5 Enfield, Rifles, Weapons, WWII

The buttstock I am using for the No.5 is a damaged SMLE stock, as a result I don’t feel guilty about the chopping I’ll be doing to it!

I make the rear band unit in the same way as in all the other Enfield builds: ERW beaten to shape and welded to the trigger guard.

_DSF9810
 

The No.5 trigger guard/magwell housing is slightly different to the other Enfields, being thinner and lighter. This makes it an even more awkward shape to cut out!

 

_DSF9811
 

The VSR gets its special parts added. The standard Vintage Airsoft quick-load VSR magazine well and the Enfield trigger that takes the trigger back into the correct location. I’ll also be using the TDC mod for this rifle of course, along with the Enfield bolt mod.

 

22496956_10155993089243623_536568108_o

In place in the roughed out stock, the gun already starts to take shape.

22555839_10212957125275633_589420679_o

I smooth out the shape and improve it a little. I still have to finish the back end where the receiver fits and around the rear band.

_DSC7308

At the front I need to create space around the outer barrel as it is free floating on the original. The top guard also needs rounding off at the front.

_DSC7309

Working on the receiver now, no standard typeface is quite right for the markings. I find some clear images to work from and create a file I can work from and tidy up in Qcad.

Screen Shot 2017-10-19 at 18.13.21

Once the basics of the typeface have been finished up, I transfer them onto the side of the receiver to be 3D printed.

Screen Shot 2017-10-19 at 20.20.00

I got the muzzle brake/foresight unit 3D printed. As well as looking the part it also holds the inner barrel centred nicely. It’s held in place with two screws that lock it in place through grooves in the top of the barrel.

_DSC7320

The outer barrel is secured in the ‘traditional’ way for my VSR builds.

_DSC7322

I’ll have to spin up the barrel on the lathe to clean it and get a consistent polish, then I can oil finish it which will be nice and wear-resistant.

_DSC7324

Polished up and oil finished, the only problem is the muzzle brake doesn’t look as good now! You will also notice that the inner barrel has been cut down and re-crowned on the lathe by this point.

_DSC7372

At the back end, I start the modifications to the butt.

_DSC7386

The buttpad and cage have been 3D printed and are fitted by hand to the wood.

_DSC7387

I’m fairly pleased with the standard of the fit. The buttpad cage is a little more fragile than I would ideally like so some tinkering may be needed.

_DSC7388

I carved out the recess needed for the sling loop in the buttstock. 

_DSC7429

The assembly so far. The receiver needs fitting, plus there are some finishing bits to do. Inevitably there will be a bunch more things that I can’t think of right now. I am very excited to finish this build and get her in the field!

_DSC7426
 

 

If you are interested in this project or have an idea of your own, drop us a line on enquiries.vintageairsoft@gmail.com to discuss. ‘Like’ our Facebook page or follow the blog to get regular updates on projects and interesting videos and articles.