G98 VSR: Part 1

G98, G98 VSR, Imperial Era, Inter-War (1918-1939), Rifles, Weapons, WWI

The start point for this project is the G98 Dboys shell ejecting model. A VSR base for this rifle would make it much more practical and skirmish able.

_DSF8004

The first step is expanding the recess for the magazine This necessitated the removal of the front securing lug for the original magwell and trimming down the metal lining of said magwell to fit the new VSR parts. Rather pleasingly the trigger sits quite naturally in the trigger guard with minimal modification.

_DSF9133

The fore-end is unchanged. I’m using the same outer barrel and fittings.

_DSF9134

The bolt handle will be another custom piece.

_DSF9136

The bolt handle will screw in and be thread locked in place. If at a later date I decide to make a bent handle for use as a sniper rifle I can just swap it out.

_DSF9137

The bolt handle part-made. At this point I had to take it off and make some other parts and the lathe broke down, so I’ll have to come back to this later!

_DSF9138

The rear sight for this is 3D printed, the repro I used won’t fit over the larger receiver. Although it looks a little rough here, once painted up it’ll look the part. In the longer term I hope to cast these in aluminium.

_DSF9365

In place on the rifle, it is secured by two screws. The small hole in the middle is for hop adjustment (I fit a TDC hop mod to all VSR builds).

_DSF9372

Viewing down the rifle, that Vizier rear sight give a really distinctive sight picture!

_DSF9376

Next to its nephew, the K98k VSR build in the workshop.

_DSF9375

A bit of epoxy resin to smooth off the rougher surfaces. When sanded down and painted up it’ll really look the part.

_DSF9418

With the lathe FINALLY fixed I could finish off the bolt handle after looking at it half finished for about two months (truly torturous). Now I just need to finish the back cap and the rifle itself is done.

_DSF9638

Then there are a few optional extras which I’ll be fitting before finishing entirely. So far though, I am delighted with how this conversion is going.

 

If you would like to see the little intro I wrote for the first G98 build you can see it here.

If you like this project or have an idea of your own, drop us a line on enquiries.vintageairsoft@gmail.com to discuss. ‘Like’ our Facebook page or follow the blog to get regular updates on projects and interesting videos and articles.

Don’t forget you can buy our complete products via Etsy.

Kar98k: Build 1

Custom builds, K98k, Weapons, WWII

Now, this is a build I’ve wanted to do for a while. Having found a keen customer who had all the parts it is now nicely underway!

This is a VSR-based build, the most practical option for a spring-powered bolt action rifle. I’m using an original stock which will be modified to take the new parts. You will be glad to hear that it isn’t a WWII period stock so far as I can tell.

_DSF9191

The action dropped in fairly easily, a square cut for the fore-end, the back being scooped out carefully to fit snugly.

_DSF9202

A view inside.

_DSF9204

The barrel, naturally, goes through the barrel recess.

_DSF9205

I then chased out part of the fore-end of the action recess all the way through the stock for the magazine well. The one slight faff with doing VSR Mausers in this way is that the faux magwell meets the real one but this is not a major issue as I’m expecting to make a new faux magwell from scratch.

_DSF9206

The outer barrel is a piece of ERW tube, which is the perfect size to use the original fittings. This will be cut to size closer to the end of the build.

_DSF9348

The VSR based rifles are still experimental at this stage, I’ve produced about four or five different magazine catch designs which I am putting into different guns for customer feedback.

_DSF9349

I’m very please with my rear sight design for this build. 3D printed, once painted up this will really look the part and gives the user elevation control.

_DSF9363

Best of all it will fit snugly onto the receiver with minimal faff. It would be nice once my casting setup is complete to make this in aluminium.

_DSF9364

On the rifle with its Uncle the G98. What you can’t see is the TDC hop mod which is part of the sight unit. This disposes of the rather finicky and annoying side adjustment arm that is the weak point in a normal VSR system.

_DSF9375

There’s still a good bit more to do on this rifle, but the framework is all there. It’s really, really comfortable and I can’t wait to get the bolt handle in place along with the last external parts and start shooting.

 

If you are interested in the history of the K98k, you can check out the introduction article here.

If you like this project or have an idea of your own, drop us a line on enquiries.vintageairsoft@gmail.com to discuss. ‘Like’ our Facebook page or follow the blog to get regular updates on projects and interesting videos and articles.

Don’t forget you can buy many of our complete products via Etsy.

 

Kar98k: Introduction

Cold War, K98k, Rifles, Weapons, WWII

After the Great War, the Treaty of Versailles (TofV) put strict limits on the number of weapons, ships and small arms. Germany, like all the major powers, had learned that short rifles were every bit as good as a long rifle for any realistic infantry use and frankly better in any situation other than firing in ranks.

As a result, they disposed of a lot of their G98 long rifles, keeping hold of far more Karibiner 98az models, though producing the so-called K98b (which was basically a G98 with a tangent rear sight and turn-down bolt) during the Weimar years. How many ‘b’s were produced is uncertain, but they don’t feature in pictures of the period.

During the inter-war years, levels of tolerance to the TofV fluctuated, with many civilian hunters and paramilitaries reluctant to give up their beloved weapons. As a result many were hidden, coming out of the woodwork to fight street battles between Communist and Fascist militias, the militias and the government and eventually into service with some government units.

K98k, with laminate stock.

In 1934, the German Army ordered a new design of rifle. The reasons of this are not entirely obvious, but given the timing one could conclude that it is related to: the re-armament of Germany and therefore standardisation on one rifle for all to simplify production and logistics. It would also allow for the removal of the G98/K98b from regular service and finally push those pesky long rifles to the reserves.

 

With this short rifle as standard, the Germans also standardised on the new s. S Patronen (previously used for machine guns) which produced less muzzle flash in the shorter barrels.

 

Early K98ks were blued, with walnut stocks, though changes were made to this as it went through its service life. Over time, laminate stocks were introduced, which were cheaper and required less processing time for the timber. Oak was used as a stand-in from 1943. Parkerisation was used to finish the metalwork on later models, making for a much hardier finish than traditional bluing.

The K98k is one of history’s iconic sniper weapons. Many were equipped with the ZF39 scope (pictured) and these were preferred by ‘true’ snipers.

Most famously, the K98k was the standard German rifle of WWII, but it was also used by Sweden and captured units by the USSR to fill gaps in their own equipment.

Later in the war the ZF41 scope was also issued. This clipped onto a mounting next to the tangent sight and could be removed quite easily. At 1.5x magnification it was unpopular with snipers and had a fairly poor field of view but it did allow sharpshooters to perform something of a Designated Marksman role as it would be called in modern parlance.

Post-war, it saw service with the Viet-Minh/Viet-Cong (Soviet captures sent as war aid), Korea, France, West Germany, Norway and Yugoslavia, all with their own local modifications. They also saw action in Palestine, where they were used against Arabs and British forces. Even in the latest Iraq War and following insurgency they were being used against Coalition Forces.

Participants of the Haganah revolt against British control of Palestine carry K98ks and a Sten MKII.

This really is just to scratch the surface. The K98k and its Mauser brethren went everywhere and did everything, much like its sister bolt-actions of the era well outlasting standard military use to serve in specialist roles even up to today with some armed forces. This is not to even mention civilian use.

 

Vintage Airsoft is currently working on a VSR-based K98k and will be posting the build to the blog as it progresses.

 

You can find more information on the K98 through these links:

Weimar rifle markings

Overview/test of a repro ZF41

Very late WWII Volksturm K98-based rifle

Norwegian Mauser

Israeli 7.62 Mauser

 

Spring SMLE: Complete.

Complete builds, Imperial Era, Lee-Enfield, Products, Rifles, SMLE, VSR SMLE, Weapons, WWI, WWII

At long last, the first spring rifle is complete! I’m quite pleased with my first attempt at a VSR based SMLE, though there are a few tweaks I shall be making to production versions.

_dsf8813

 

 

 

_dsf8814

I think in future versions I shall sit the action lower down in the stock to achieve a lower profile. Then I can add things like a charger bridge, maybe even splitting the back of the receiver for added authenticity.

_dsf8816

This example is using an original rear sight leaf. In future versions I hope to make reproductions to minimise the number of irreparably modified originals. The rear sight will also host the TDC hop adjustment mod, saving you a helpful upgrade.

_dsf8817

I may have to use No. 4 Enfield swivels unless I can find a way to reproduce these, swivels are becoming harder to come by.

_dsf8818

After the success of the 3D printed Sten MkV foresight, I have continued to use this technology here to create the outer barrel impression and foresight unit.

_dsf8819

The barrel has been trimmed down to fit. The VSR barrel is a little long so I removed it, cut and re-crowned it on the lathe.

_dsf8820

Here’s an important feature, I have lined the magazine well with steel which means magazine release should be consistent and not pinched by the wood. Other VSR Enfields don’t have this lining and I have seen magazines get stuck. There is a new design for this which I will use in the production versions to allow very fast magazine changes.

_dsf8821

The fake magazine is solid resin, painted to look right. There is no need to destroy a perfectly good magazine for this build!

_dsf8822

The original buttplate. I’m hoping to make reproduction ones for future versions. As this is an original buttstock you would still be able to fit an original if this happens.

_dsf8823

I’m hoping to improve the bolt handle and back of the bolt shape. However I am pleased with where it now sits, nice and authentic on the rear band you can achieve quite a good rate of fire.

_dsf8824

So, there are some changes to come for production but I’m very happy with this first go!

You can see the whole VSR SMLE build here and a potted history of Lee-Enfield development here.

If you are interested in this project or have an idea of your own, drop us a line on enquiries.vintageairsoft@gmail.com to discuss. ‘Like’ our Facebook page or follow the blog to get regular updates on projects and interesting videos and articles. 

Don’t forget you can buy our complete products via Etsy. This will be available soon.

Spring SMLE: Part 4

Imperial Era, Inter-War (1918-1939), Lee-Enfield, Rifles, SMLE, VSR SMLE, Weapons, WWI, WWII

I’ve had the mould sitting about from previous projects for SMLE magazines. I took a resin cast from this, cut it down to size and added some screws into the top to secure to the gun. I painted it with acrylics, which are great for getting metallic and weathered finishes.

_dsf8698

I’ve removed the rear band assembly to do some detailing and finishing work.

_dsf8716

I thought I would attach a few pictures of the band before being cleaned up here as I forgot to show the build process for this part. I’ll let you work out the details…

_dsf8717 _dsf8718

Markings will be kept simple for this, no attempt to replicate the originals as they would require a very random set of stamps.

_dsf8719

As I’m replicating various Mks of firearm I can’t use the Mk system to denote changes in the designs of the airsoft versions as ‘SMLE No.1 MkIII MkI’ is a bit confusing! However I’m not going to stamp ‘V0.1’ onto this as it would look out of place, so it will be denoted as MkI. Confused yet? Yeah, me too.

_dsf8720

Now it’s clean and marked up, it’s heated up and into the oil it goes for that lovely, black satin finish.

_dsf8721 _dsf8735

 

 

 

 

 

Finally, screwing on the buttplate and some last finishing touches before assembly….

_dsf8810

 

You can see the whole build so far here and a potted history of Lee-Enfield development here.

If you are interested in this project or have an idea of your own, drop us a line on enquiries.vintageairsoft@gmail.com to discuss. ‘Like’ our Facebook page or follow the blog to get regular updates on projects and interesting videos and articles. 

Don’t forget you can buy our complete products via Etsy.